I am new to the Rotel sound, but from what I have heard so far, I am impressed. I intend to purchase an RB-1080 with RC-1070 Pre. Are there any inherent issues plaguing the RB-1080? ;x(
-
-
There's a fuse blowing issue that can happen with certain speakers (seems random) and using the 12v trigger.
Rotel believes they have fixed the issue (I've only seen one report of it on ones that have the fix). If you want to be sure, get a new one and verify that the fix has been applied. In reality though, you have a 99.5% chance of not having a problem.
Kevin D. -
I second that, I've been running the RB-1080 using the 12v trigger for some 3 months now and having no problems what so ever.
The previous owner of the amp used to run tests on different DIY speakers, with many different loads put onto the amp. ranging from light (8 ohm nominal) to very difficult loads (down to 2 Ohm on some frequencies). Still, this amp does not break.
There are some units that have problems, but they are few and far between.
If you do purchase the RB-1080, do make sure you keep it well ventilated, as this machine does run hotter then expected.Comment
-
My rb-1080 runs perfect. No problems what so ever. Just make sure it has the dual binding posts on the back for each speaker output. And that it is a V3 model.Comment
-
Hi. I have owned both the RC1070 and RB1080 without incident. The amp has performed flawlessy for me since I purchased it in May 2004. I do not use the 12v trigger as I learned of potential issues with this connection through this forum. I leave my amp on all the time. While the top of amp does get warm, it is not uncomfortable to touch.Comment
-
Thanks for the input. I plan on buying one from a local dealer and I will be using PSB Stratus Mini's. I will be sure to confirm that the 1080 is the latest model. I have been using a RX-1052 Receiver and I intend to return it to my dealer. For some reason my dealer seems hesitant to accept the exchange. I just purchased it on January 11, 2006 and there is not a scratch on it.Comment
-
Why do you want to return your 1052? Is your Dealer The Home Theater Store?Comment
-
No, it is not the Home Theatre Store in NY. It is a local dealer. What happened was that I promised myself that the RX-1052 would get me through the year until I returned to seperates. However, as soon as I purchased my new PSB Mini's and listened to them I got the upgrade bug again. These Mini's are neutral and provide a deep and powerful soundstage. I want to get the overhead the RB-1080 would provide. I should have thought it over before purchasing the RX-1052. This receiver sounds wonderful and it sounds better than some amps I have owned but I quickly realized just how much better the seperates would sound...maybe I'm being too picky.Comment
-
Hi,
I have recently picked up a Rotel 1570/1575, and I am having a few problems with the 12v trigger between the 1570/1575. I am unable to get the 1575 to power on while using the trigger when turning the 1570 on. I have the trigger cable connected to trigger out 1 on the 1570, and the... -
Does anyone know, why RB-1090 does not has 12V TRIGGER input ? I'm planning to get one near future, been reading alot about the RB-1090, but when I looked at the back panel drawing of the RB-1090 on Rotel site, it's does not show 12V TRIGGER input on its back panel, Is there a reason for it, not to... -
Hi all,
I almost posted this in my other thread, but thought maybe it could use its own. A few weeks ago I picked up an iNuke 6000DSP to run my LFE channel. These amps are amazing to run subs. The extra headroom for my drivers has added a very audible benefit to my system - and the DSP... -
I use two 12v triggers on my RSP 1098, one triggers a RLC-1050 power distributor (which in turn powers on a RB-1090) while the other triggers a RMB-1075. Everything worked fine until a few weeks ago when the RSP 1098 started to interrupt the 12v trigger to both components at random after power on. When... -
Hello guys,
I've been searching this kind of question regarding on 12v trigger it seems that most of the topics is about RB-1080 and getting some problem like bad fuses, L&R ch not working due to resistor, caps and etc. Just wondering if there's anyone here encounter same problem...
Comment