Receiver vs. adding amp

Collapse
This topic is closed.
X
X
 
  • Time
  • Show
Clear All
new posts
  • corysmith01
    Member
    • Feb 2005
    • 51

    #1

    Receiver vs. adding amp

    I posted a few days ago asking about the differences bt a 1055/1056. I'm on the used market looking to get a new receiver. Reason being is that I just acquired some new 4 ohm speakers. I currently have a Denon AVR-3805. A fairly robust receiver, but I still have read that the likes of Rotel and NAD might be better suited, if going the receiver route, for 4 ohm speakers. Well, I'm now wondering if an amp might be a better solution. BUT, I'm trying to figure out what's best for the money as I'm not loaded with cash.

    So, the way my brain has broken it down is like this:

    Scenario A: Sell the 3805 (+~$500) and purchase used 1056 (~$750). So, my total out of pocket cost is a mere $250. Not bad.

    -OR-

    Scenario B: Keep the 3805 and buy an RB 1050 ($400 new/~$300 used) or an RB 1070 ($700 new/ ~$475-$500 used). In this scenario, my out of pocket is anywhere from $300 on the low end to $700 on the high end.

    I'm in a very small room and never need to crank my system, so keep that in mind...just in case this comes down to pure power based suggestion. I'm in an apartment and am always at low to moderate levels. Oh, and it's a 2.1 system. No center (I just run phantom). No surrounds.

    So, I guess I'm torn bt. what to do. The $250 outlay (A) seems tempting as it's so little out of pocket. But, just adding a piece of gear (B) as opposed shipping/receiving seems a lot easier...though more costly.

    Given the two choices, what would you guys chose? I've deliberated this for a while and can't come to a definitive conclusion. They both seem like good options. But am I missing something? Is there a clear winner? Thanks for the help.
  • gianni
    Senior Member
    • Nov 2002
    • 524

    #2
    Cory,

    As 1055 owner I'd advise you to go with the 1056. The Rotel receivers excel at music compared to most in this price range. The amp sections are very good for a receiver.

    If you do a search, you'll see where I did some testing with an amplifier over 3 times the price of the RB-1070 and found very few advantages. This was with 4 ohm speakers of about 89db sensitivity in a medium sized room.

    Unless you really need the power, I doubt an outboard amp will do as much for you as would an RSX-1056. The preamp section also affects sound quality and Rotel did a good job on the RSX-105x series receivers.

    Comment

    • mike c
      Senior Member
      • Dec 2005
      • 307

      #3
      you have to do a side by side comparison of the features of both the denon and rotel receivers and see if there are features you can live without.

      Comment

      • calmac
        Senior Member
        • May 2005
        • 110

        #4
        Originally posted by mike c
        you have to do a side by side comparison of the features of both the denon and rotel receivers and see if there are features you can live without.
        You have to do a side by side comparison of the Denon and Rotel and see if there is sound quality you can't live without
        Gordon

        Comment

        • hifiguymi
          Super Senior Member
          • Mar 2007
          • 1532

          #5
          If sound quality is one of the driving forces, I'd strongly consider just the receiver upgrade. The sound quality of the preamp section in the Rotel is better than the Denon and that makes a huge difference over all. If you don't/can't listen at high volumes and don't need the extra power, then the the sperate amp just doesn't make sense. Only if you plan on using the amp as a stepping stone to seperates, does it make sense. Plus you wouldn't be losing much in terms of power anyway. The AVR-3805 is rated at 120 w/ch with only two channels driven and the RSX-1056 is rated at 100 w/ch with two channels driven.

          You wouldn't be losing much in the way of features to make the change in receivers so that shouldn't be a concern.

          Best of luck.

          Eric

          Comment

          • cfrizz
            Member
            • Apr 2006
            • 51

            #6
            I would go with a separate amp rather than another receiver. That way you can keep the amp whenever you decide to upgrade either to another receiver or to go to a preamp instead.
            Cathy
            ---------
            Sunfire TGP III, Sunfire Cinema Grande 405wpc 5 channel Amplifier, :B Rotel RCD-1072 CDP, Onkyo TA2600 Tape Deck, Pioneer Elite 47-A DVD, Sony 32" XBR TV, Sony PS-454 Turntable, Polk RTA-8T Main Speakers, Boston 920 Center Channel, Boston PV600 Sub Woofer, Polk FXi-3 Surround Speakers

            Comment

            • dmcgowan
              Senior Member
              • Sep 2003
              • 134

              #7
              Cory,

              Based on my experience the past week, make sure you let your ears decide through your speakers...

              But given you're talking about 2ch music, I suspect the RSX-1056 will be the better choice.

              Comment

              Related Topics

              Collapse

              • Fred7
                RSX 1056 Stereo Mode
                by Fred7
                I just upgraded from a RSP-1066 and a RSX-1055 to a pair of brand new RSX-1056 receivers, one for my living room and one for my bedroom. One of the main reasons that I upgraded was to get true analog bypass for two channel and multi channel inputs. I was also looking forward to using the two channel...
                14 July 2004, 00:12 Wednesday
              • Cooldmitriy
                Connecting receiver 1056 with home PC question
                by Cooldmitriy
                Hello folks,

                I just received my new 1056 receiver and would like to ask you a question. I noticed RS-232 port in the back of the unit for computer connection. The main purpose of that port is to perfom firmware upgrade of the unit.

                Is there any way to connect my...
                18 October 2005, 12:45 Tuesday
              • Noddy347
                Mixing av receiver and amplifier brands?
                by Noddy347
                I currently have a Rotel receiver(1056) and a five and two channel Rotel amps running the theatre setup. If I was to replace the receiver with a denon, onkyo receiver will there be a difference in the sound style even though I will bypass onboard amps and use the Rotel power amps to run the theatre?...
                15 February 2011, 01:05 Tuesday
              • thor
                Receiver or seperates ?
                by thor
                hi forum,

                i plan to buy a new system and can“t decide what to take - a receiver
                (1056) or seperates ? but which to take ? anyone can help me ?

                5ch is ok for me - but maybe for the future it would nice to be able to
                upgrade to a 7ch system

                thanx...
                21 January 2004, 15:30 Wednesday
              • EdwinRotelUser
                Problems with external remote input Rotel RSX-1056
                by EdwinRotelUser
                Hello,

                I have a Rotel RSX-1056 Surround Receiver. I have problems with the external remote input of the RSX-1056.

                The problem is that the RSX-1056 don't react on the sent IR-signal via the external remote input. Controlling the RSX-1056 with the remote via the internal...
                14 March 2005, 04:25 Monday
              • Loading...
              • No more items.
              Working...
                Searching...Please wait.
                An unexpected error was returned: 'Your submission could not be processed because you have logged in since the previous page was loaded.

                Please push the back button and reload the previous window.'
                An unexpected error was returned: 'Your submission could not be processed because the token has expired.

                Please push the back button and reload the previous window.'
                An internal error has occurred and the module cannot be displayed.
                There are no results that meet this criteria.
                Search Result for "|||"