Elite Receiver owners, has this ever happen to you?

Collapse
This topic is closed.
X
X
 
  • Time
  • Show
Clear All
new posts
  • John Holmes
    Super Senior Member
    • Aug 2000
    • 2707

    #1

    Elite Receiver owners, has this ever happen to you?

    My volume knob gets stuck every now and then when using the remote. When it does it, I'll move it manually and it seems to be fine for awhile. Is this the begining of a bigger problem to come?




    "I came here, to chew bubble gum and kickass. And I'm all out of bubble gum!!!" My DVD's
    "I have come here, to chew bubblegum and kickass. And I'm all out of bubblegum!!!"
  • George Bellefontaine
    Moderator Emeritus
    • Jan 2001
    • 7636

    #2
    Hi, John-
    I had a similar problem with a Yamaha, but it was with the input selector dial.My son. who's a tech said it was probably dirty and needed cleaning.I still haven't got around to cleaning it. I only use it for music now. But I did notice a difference when I changed the remote batteries.It didn't seem to stick as much. Don't know if this is any help or not.
    Regards,
    George




    My Homepage!
    My Homepage!

    Comment

    • John Holmes
      Super Senior Member
      • Aug 2000
      • 2707

      #3
      Thanks for the info George! The knob is motorized I believe not electric so, I'm not sure if a dirty contact is applicable. But you maybe right. Also, I have only had it for just about a year. I would hope that dirt has not become an issue this soon. I will try the battery change.

      Again thanks.




      "I came here, to chew bubble gum and kickass. And I'm all out of bubble gum!!!" My DVD's
      "I have come here, to chew bubblegum and kickass. And I'm all out of bubblegum!!!"

      Comment

      • Lex
        Ultra Senior Member
        • Apr 2001
        • 27460

        #4
        Sounds like either motor going bad, or it's fighting resistance of some kind. Could be a slightly bent shaft, dirt and grime, or yes, operator error, lol. (jk). You might try removing the set screw if it has one, and sliding knob off. Clean area and replace. Perhaps some electronics lubricant as long as it's not a danger to get inside the component. That's my best advice.

        Lex
        Doug
        "I'm out there Jerry, and I'm loving every minute of it!" - Kramer

        Comment

        • John Holmes
          Super Senior Member
          • Aug 2000
          • 2707

          #5
          Thanks Lex. Of course, since posting this thread it has not shown it's ugly head. When it does, I'll try some of the above.




          "I came here, to chew bubble gum and kickass. And I'm all out of bubble gum!!!" My DVD's
          "I have come here, to chew bubblegum and kickass. And I'm all out of bubblegum!!!"

          Comment

          Related Topics

          Collapse

          • alkalay
            1068 - A loose volume knob
            by alkalay
            Hey rotelian mates,

            Has any of you experienced a loose volume knob on a 1066, 1068, 1098 or any other Rotel's pre, integrated or receiver?

            My 1068 exhibits this looseness when turning the knob to one direction and then to the opposite one. First I thought it was normal...
            06 February 2005, 14:08 Sunday
          • Blaine
            my dirty crap
            by Blaine
            OK I feel like maybe there might be someone else out there who might benefit from seeing dirty crap projects, instead of the immaculate magnificence we have all become accustomed to on this forum, so I am posting pictures of my dirty crap if I can figure out how. I am also not going to clean up said...
            07 May 2010, 05:52 Friday
          • PiDD
            Rotel 1098 Function knob preference poll
            by PiDD
            Please take the time and cast your vote!

            Here is the issue. A recent SW upgrade puts a delay in the function knob. This really comes into play when I am labeling inputs.. as five clicks forward only takes me 4 places. (when I move the knob fast)

            This really drives me...
            Yes it drives me crazy!
            42.11%
            8
            No I like it!
            10.53%
            2
            They changed something... I didnt notice!
            47.37%
            9
            19 July 2005, 14:00 Tuesday
          • Rael
            Problem With Volume Knob on 1068
            by Rael
            I've owned my 1068 processor for a couple of years now and never had any problems until recently. All of a sudden, the volume knob has a mind of its own. When I go to turn it, it will suddenly jump from 58 down to 35 or even all the way to max! It doesn't matter if I turn it up or down, I never know...
            22 November 2008, 07:09 Saturday
          • Ron Reda
            "Knob" Light?
            by Ron Reda
            I just got my 1066 pre/pro last night and noticed that the blue surround around the central knob wasn't lit up. I could've sworn that, in some of the pictures I've seen, there was a light around the center knob. Am I just hallucinating???
            29 January 2003, 09:50 Wednesday
          • Loading...
          • No more items.
          Working...
            Searching...Please wait.
            An unexpected error was returned: 'Your submission could not be processed because you have logged in since the previous page was loaded.

            Please push the back button and reload the previous window.'
            An unexpected error was returned: 'Your submission could not be processed because the token has expired.

            Please push the back button and reload the previous window.'
            An internal error has occurred and the module cannot be displayed.
            There are no results that meet this criteria.
            Search Result for "|||"