PT-AE900U - Main power switch - ON or OFF?

Collapse
This topic is closed.
X
X
 
  • Time
  • Show
Clear All
new posts
  • Frits
    Junior Member
    • Mar 2006
    • 6

    #1

    PT-AE900U - Main power switch - ON or OFF?

    When I turn off power on my Panasonic PT-AE900U projector, it will go into stand-by mode following cool-down (the system light will go to RED).
    Is it advisable to then turn off the main switch on the physical projector, or can I just leave it in stand-by mode? The manual states that in stand-by mode there is a consumption of 0.8W, but are there other things that I should be aware of?

    Frits
    Frits
  • Kobus
    Senior Member
    • Aug 2005
    • 402

    #2
    Leave it on (stand-by), it is designed for that.
    Anyway, 90% of people have the projector mounted in such a way that they can not reach the switch.

    Kobus

    Comment

    • George Bellefontaine
      Moderator Emeritus
      • Jan 2001
      • 7636

      #3
      I never use standby. But it doesn't matter. I have two pjs and they are connected to a power outlet with an on/off switch. After the pj cools down and goes into standby mode, I then switch it off. I have had many projectors over the years where I used this practice and have never had any problems. But I don't use my theater every day. If I did, I would probably use the standby mode. But more out of convenience than anything else. It's really a matter of preference. It doesn't hurt to switch off your projector as long as you wait for the cool down fan to stop running. The manual will actually tell you to do exactly that if you are going to be away or not using the pj for a long period of time.
      My Homepage!

      Comment

      • Azeke
        Super Senior Member
        • Mar 2003
        • 2123

        #4
        Frits,

        Welcome to HTGuide :welcome:

        I actually have a switch to control the circuit, which is mounted on the ceiling to control the Panny 900U. After the projector fan cools the lamp, I usually turn off the switch, however it seems with the Panny it just goes straight into standby mode without anything running. My previous projector would continue to run, the Panny 900U is dead silent and only draws 0.08W of power in standby mode. That being said I will continue to turn the projector off by the switch just in case of power surges, etc., unless of course my wife turns of the equipment by the remote (macro controlled), but I feel much better about that now.

        BTW, this is a fantastic projector, I am certainly enjoying it. I have just mounted it on the ceiling (had to modify my previous ceiling mount). Panasonic has also extended the $400.00 rebate, this is a great bang for the buck projector. I have recommended this projector to a couple of friends who have taken advantage of the rebate.

        I hope you are enjoying your projector as well.

        Peace and blessings,

        Azeke

        Comment

        • Chris D
          Ultra Senior Member
          • Dec 2000
          • 16875

          #5
          I personally have never used anything other than standby mode on my AE700. Has worked great for me.
          CHRIS

          Well, we're safe for now. Thank goodness we're in a bowling alley.
          - Pleasantville

          Comment

          Related Topics

          Collapse

          • rofafor
            RSP-1068 standby mode & optical input glitches
            by rofafor
            I upgraded my hifi gears to Rotels in June. The RSP-1068 was an obvious choice and tested it with RMB-1075 amp too. However the RMB-1075 and my speaker setup (Amphion Argon 2) didn't bring the same feel of sensation as Genelec active speakers, so my RSP-1068 is now connected to a nice set of Genelec...
            03 August 2004, 13:14 Tuesday
          • Kobus
            CDP transport issue
            by Kobus
            Has the issue regarding reading the first disk been addressed. I see there is no firmware update for this. Also no further discussion by those of you affected. I am surprised as it is a couple of months now.
            The reason I am asking is that a friend recently got a 102 with the same issue.
            ...
            15 February 2007, 09:00 Thursday
          • Slice
            RSP-1068 DPLIIC Default Mode won’t stay configured.
            by Slice
            Have had the setup for 2 months and everything has been fine until now. The other night I had company over to watch a movie. I activated Video 2 [assigned to DVD with Default Mode set to DPLIIC] but it came up in Bypass mode.

            The OSD System Status showed:
            Listen: DVD...
            15 March 2005, 16:40 Tuesday
          • sergiok
            Rsp 1068 Standby Mode
            by sergiok
            hi guys my 1068 power on light used to only come when being used & switch off when in standby mode.now its on all the time.is it something to worry about?
            06 July 2006, 01:37 Thursday
          • Bluespower
            1068 Stuck in Standby Mode
            by Bluespower
            Got home tonight and found that my 1068 would not power up out of standby mode. I cycled the on/off switch on the back of the unit a few times with no luck. I disconnected the power cord and waited a few minutes and still no luck. Is there something else I can try OR is it ship it to the repair center...
            17 July 2006, 20:44 Monday
          • Loading...
          • No more items.
          Working...
            Searching...Please wait.
            An unexpected error was returned: 'Your submission could not be processed because you have logged in since the previous page was loaded.

            Please push the back button and reload the previous window.'
            An unexpected error was returned: 'Your submission could not be processed because the token has expired.

            Please push the back button and reload the previous window.'
            An internal error has occurred and the module cannot be displayed.
            There are no results that meet this criteria.
            Search Result for "|||"