RSP 1068- fading display

Collapse
This topic is closed.
X
X
 
  • Time
  • Show
Clear All
new posts
  • RoMan
    Senior Member
    • Jan 2007
    • 212

    #1

    RSP 1068- fading display

    Hi all,

    My display on my RSP 1068 preamp is starting to fade out. For example the subwoofer letters seem really dim. I have it turned up to bright on my remote but the letters are dim with certain functions on my display.

    Is it possible its a fuse that needs to be replaced? Any advice is most appreciated on how to remedy this situation. Thanks again.

    RoMan
    :T
  • srb
    Senior Member
    • Oct 2004
    • 311

    #2
    There is a Display Refresh Procedure that might remedy your situation.

    Steve


    Date: March 13, 2006
    Models: RSX 1056, RSX 1067, RSP 1068
    Subject: Front Display Refresh Procedure

    The fluorescent front display of the RSX 1056, RSX 1067 and the RSP 1068 utilizes a dot matrix display consisting of hundreds of pixels, which illuminate as needed. Over time, the pixels that are used frequently will remain fully illuminated, while those pixels that are not illuminated often may lose brightness. Refreshing the front display periodically will ensure that all pixels are restored to their full illumination across the display.

    For this purpose, there is a refresh procedure that enables the display to be refreshed at any time. Activating the refresh mode of the unit will illuminate the entire front display, and after a period of time, all pixels will be equally bright. Depending upon how frequently the display is refreshed will determine how long the refresh period needs to be – at most a period of about 4-5 hours should fully refresh the display, or less time if done at regular intervals.

    To activate the refresh mode of your unit, place the unit into the standby mode. Next, press and hold the “2CH” and “MUTE” buttons on the front panel simultaneously while powering the unit on with the remote control. The unit should power on with all the pixels of the display illuminated and the front panel buttons can be released at this point. The unit is fully functional while in the refresh mode and the unit can be put into the standby mode and the display will remain in the refresh mode. The refresh mode will be deactivated once the unit is brought back out of standby.

    If you have any questions, please contact our Technical Support Department at 800-370-3741.

    ROTEL OF AMERICA  54 CONCORD STREET  NORTH READING, MA 01864  PHONE: 800-370-3741  FAX: 978-664-4109

    Comment

    • windshear
      Senior Member
      • Dec 2004
      • 243

      #3
      Check out this thread.

      Comment

      • RoMan
        Senior Member
        • Jan 2007
        • 212

        #4
        Thanks srb and windshear. I'll try it out. This forum is great. Lots of knowledgeable Rotel folks whose timing always right on for help and willingness to assist those in need of information. Awesome.

        RoMan

        Comment

        Related Topics

        Collapse

        • Lex
          KE32TS2 32 inch plasma display
          by Lex
          Well, I quitely added this TV to supplement my front projection since I saw real quickly that I was going to crank a lot of hours on my PJ in a hurry. It's an HDTV monitor, the following applies: (Extracted from Plasma Depot since it was actually better than Sony's writeup.) I won't address each feature...
          12 October 2003, 21:33 Sunday
        • Chris D
          120 Hz Refresh Rate technology
          by Chris D
          So when I first heard people talking about the 120 Hz refresh frame rate technology a while ago, I didn't put a lot of stock in it. Lots of new technologies come up, and many of them make small gains.

          What the refresh frame rate does is say how often the display updates its picture....
          09 October 2007, 01:05 Tuesday
        • RebelMan
          RSX-1056 LFE in 2CH Mode.
          by RebelMan
          The LFE is illuminated on the display of my RSX-1056 when I am in 2CH mode. Does this mean the lows are sent to the sub by default? Do I need to disable the LFE (from the display) in order to get the low signal passed to the L/R channels? Can this be done using the remote (or on the box) without...
          26 April 2005, 17:19 Tuesday
        • sam2944
          Rotel RSP 1068 display dull
          by sam2944
          Hi, my 1068 pixels are dull, I did the refresh procedure few times without better result. There is any way to increase brightness via head unit or remote? Thanks
          24 November 2017, 21:48 Friday
        • htsteve
          Display Refresh for 1067,1068,1056/7
          by htsteve
          Rotelians,

          For those that have the 1056, 1067 or 1068, attached is a procedure to refresh the display screen. I tried it. It's easy to do and it works....
          05 August 2006, 14:26 Saturday
        • Loading...
        • No more items.
        Working...
          Searching...Please wait.
          An unexpected error was returned: 'Your submission could not be processed because you have logged in since the previous page was loaded.

          Please push the back button and reload the previous window.'
          An unexpected error was returned: 'Your submission could not be processed because the token has expired.

          Please push the back button and reload the previous window.'
          An internal error has occurred and the module cannot be displayed.
          There are no results that meet this criteria.
          Search Result for "|||"