Upconversion problems with 1056

Collapse
This topic is closed.
X
X
 
  • Time
  • Show
Clear All
new posts
  • angelo
    Junior Member
    • Aug 2004
    • 19

    #1

    Upconversion problems with 1056

    I don't know if anyone else is experience this, but my 1056 is doing
    component up-conversation from a s-video direct-tv tivo/receiver. When
    changing the channel the pq gets very distorted occasionally. It
    usually, but not always, happens when I have been watching TV for a
    while. If I go direct to the TV then the pq is crystal clear. I
    originally thought that it was a bad Hard Drive in the direct-tv tivo,
    so I had the unit replaced and the new one is also doing the same. I
    also tried a regular (non tivo) direct-tv receiver and the same thing
    happens. I am really frustrated because this was one of the selling
    points for me when considering the 1056 over the 1055 due to claims of
    better pq according to my dealer.

    Any ideas of help would be greatly appreciated.
  • basementjack
    Senior Member
    • Dec 2004
    • 191

    #2
    help us out here - a little more detail,

    when you change channels and it gets a little more distorted, is it just for a second, or are you saying that if you watch one channel for an hour, it's fine, then switch and it gets worse and stays worse?

    Also what kind of tv do you have?

    Comment

    • angelo
      Junior Member
      • Aug 2004
      • 19

      #3
      Thanks for your reply.

      It's for 2 to 5 seconds when a channel is switched. It never stays distorted for a long time.
      The TV is a Sony Rear Projection KP-51HW40.

      Comment

      • GosonFletchy
        Senior Member
        • May 2004
        • 183

        #4
        It sounds to me as though there is something strange going on with the video output when you change channels. The reason I think this is because it sounds like the receiver is having to "re-sink" to the video when you change channels but then sinks up again and everything is fine. I do not have any personal experience with TiVo but maybe others out there have one and have the same issue. Do you have this problem with a DVD player, or some other device, if you change inputs and then back or stop and restart movie, etc..?

        G.

        :assimilate:

        Comment

        • angelo
          Junior Member
          • Aug 2004
          • 19

          #5
          So I tried with my DVD player and the picture never distorts.
          I agree that it must be a re-sink issue.
          I wonder if it because of the dual tuner??? Tivos have dual tuners so that you can watch TV on one channel while the other channel is being recorded.

          The only catch is that it happened also on a non-tivo receiver with only one tuner.

          Comment

          Related Topics

          Collapse

          • David Meek
            TIVO Problem
            by David Meek
            I've run into a problem with my TIVO that crops up on occasion. When it automatically changes channels before it starts recording, about 25% of the time when it's changing from a station in the 500's or higher, it will not go to the proper channel. I'll wind up with "The Shopping Channel"...
            12 February 2003, 10:59 Wednesday
          • Kirby
            Upconversion problems with 1056
            by Kirby
            I just purchased a new 1056 about a week ago. I really like the sound although I am a littel disappointed with the level of hiss when the volume is high. My other problem is the poor upconversion from both composite and S-video up to componet video. The TV is displaying faint vertical bars when either...
            19 October 2004, 18:47 Tuesday
          • RACER4551
            Rsp-1068 Video Upconversion
            by RACER4551
            Just looking for input on anyone who has used the video upconversion feature on the 1068.I have been contemplating whether to do this with a couple of my components.Right now i have my dtv tivo run with s-video to my tv and was curious if it would be worth running it through the rotel and then component...
            11 July 2004, 21:05 Sunday
          • Glenn
            Rotel 1056 OSD
            by Glenn
            It is my understanding the new Rotel RSX-1056 will have video upconversion. Thus, regardless of the video type going into the 1056, all signals can be sent out from the 1056 to the TV, via a single component video connection.

            If the above is correct, two questions:

            1. Can...
            07 February 2004, 14:30 Saturday
          • Kirby
            1056 to 1068/1075 combo worth it?
            by Kirby
            As you probably know from my other posts I have been a little peeved with my 1056 due to a snapping sound from my speakers and the video upconversion. While I have had problems, I can't live without the nice Rotel sound. I am going to return my 1056 for either a new 1056 or upgrade but it is a little...
            31 January 2005, 18:22 Monday
          • Loading...
          • No more items.
          Working...
            Searching...Please wait.
            An unexpected error was returned: 'Your submission could not be processed because you have logged in since the previous page was loaded.

            Please push the back button and reload the previous window.'
            An unexpected error was returned: 'Your submission could not be processed because the token has expired.

            Please push the back button and reload the previous window.'
            An internal error has occurred and the module cannot be displayed.
            There are no results that meet this criteria.
            Search Result for "|||"