I just got the 601 S3. They are great. My receiver is a Sony 940DB rated 120wx5 (It's about 5 years old). I seen a lot of people talk about using Rotels to power their speakers. My receiver has preouts. What amp should I get to get the most out of the speakers? I'm new and need help.
-
-
I think rotel amps are a good fit with the 601 s3 but I think you need to think where you want to go with your set up. You know down the road maybe go with a pre/pro. Or just a receiver if you like the sound of your sony then stick with it until you know what way you want to go. If you want an amp maybe go with the rbm 1070 and you could always go with the rsx-1057 later for 7.1 I think it is all what you think sounds good to you. -
I want to keep the receiver
I want to keep the Sony for now, so I was looking at getting another amp to power the speaker. I will eventually go to 5.1. I will primarily use the speakers for HT.
Would it be better to go the component route with Rotel or just get a Yamaha 2600?
I want something that I flexible that I can use for a long time.
I was thinking about getting a used rmb-1066. Would I be able to used this with my current set up? Would i notice a huge improvement?Last edited by jleecov; 20 July 2006, 06:31 Thursday.Comment
-
The yammy is a decent performer, especially if driving only 2 pairs of speakers, plus you'll get HDMI 1.1, and some decent DSP modes. However, a Rotel receiver would sound better for stereo listening IMO.
Purely for HT, going cheaper with a yammy might be better, you could add an amp lik a 1077 for HT down the road, and eventually upgrade to a pre/pro that is a bit higher end...Comment
-
Well if you go the seperates route, then you can upgrade as needed (or as you see fit). If you get the yamaha, it's going to have about the same amount of power you have now, but will have lots of new features over your Sony...
Ideally, getting rotel pre/pro & amp would be your best. The Yamaha is good and you could still add an amp later on. Just depends on how much you have and can afford.
The RMB-1066 is definitely nice, not a slouch by any means.Digital Audio makes me Happy.
-DanComment
-
Got a RMB-1066 from Ebay
I just bought the 1066 from Ebay. What is the best way to use it? Should I use it in bridge mode with the front three speakers?
Thanks for all the help.Comment
-
yes, bridge the 1066 for the front 3 speakers and use your receiver to power the rears.Comment
-
Hello,
I'm getting ready to use my Yamaha RXV-3000 as an amp with a Rotel RSP-976 for surround / music processing. A amp will be purchased after saving $$$ but this is the way I'll do it for now.
Anyone else using a receiver as a amp???? -
I just got a pair of 705's to upgrade from 601 s3's that I was using in my HT/Audio system. I use a Yamaha receiver, sony cd player, HSU 12" sub B&W LCR60 ctr, Boshe ton Acoustics in wall surrounds. The front speakers are wired with home made CAT5 wire, bi-wired with 9 strands going to ea.... -
Not looking for a pre/amp combo.Looking to buy a good high current 2 channel stereo receiver.For 683's music only.I have tried the Rotel 1057 receiver -Rotel RB1080 200Watt x 2 combo and though it was ok...it is not the sound I am looking for.Was bright in my opinion.Looking for a no frills (no video... -
I have the following speaker setup:
DM604 S3 (Fronts)
M601 S3 (Rears)
LCR600 S3 (Centre)
SVS PB12 ISD (Sub)
I think I cheaped out too much on the receiver (Yamaha RX-v750). The Yammie has a nice array of processing modes for HT and the auto level set... -
First post guys sorry it's so long.
This is the plate amp I have from Creative Sound Solutions Power Output @ 8ohms/4ohms250W/360WTHD0.08%S/N ratio @ rated power100dBInput sensitivity @ 100Hz low level150mVInput sensitivity @ 100Hz high level5VInput impedance22KohmsVariable low pass X-over frequencies40-160HzWeight17lbs/7.7kgsDimensions...
Comment