1570 dvi help

Collapse
This topic is closed.
X
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • AudioDude
    Junior Member
    • Jan 2009
    • 8
    #1

    1570 dvi help

    Hello,
    When connecting to my tv via dvi the 1570 will not play audio from my blu-ray player. I know dvi doesnt carry audio but the audio should still get to the 1570 via the hdmi connection. Anyone have this problem and contact Rotel. Anyone have a solution?
    Tags: None
      • Bottom
    • Kevin D
      Ultra Senior Member
      • Oct 2002
      • 4601
      #2
      Known issue with certain Tv's whose DVI inputs do not handle HDCP encryption. (And a few that do, but not correctly).

      You might be able to work through it with them if you know your TV fully supports HDCP. Or you could not use the HDMI output on the 1570, run component video from the player direct to the TV, and only run HDMI from the player to the 1570 to get audio. You could then use the component video inputs for the rest of your sources ran to another component input on your TV.

      Or you could buy a new tv..

      But the best bet is to pick up a HDFury2 HDMI to component video converter. It fully supports HDCP and will then send the video signal on to the TV as component video. Moome also has an HDMI to DVI converter that just strips the HDCP signal off and should work as well.

      Kevin D.
        • Bottom

        Comment

        • rja52
          Junior Member
          • Jan 2009
          • 4
          #3
          I have (had) same problem. I tried an HDMI to DVI adaptor between RSP-1570 and TV. Didn't help. Also tried an Oppo HM-31 HDMI switch that I had been using for something else. This didn't work either. Finally I purchased the HDFury2 and it does the job. I contacted Rotel via phone and email and did not hear from them.
            • Bottom

            Comment

            • Alfred
              Junior Member
              • Apr 2009
              • 26
              #4
              I have the same problem. It seems that the main cause is the enhancements for EDID in HDMI. With HDMI (against DVI) the transfer of audio information is possible. If there is a DVI (with HDPC) connected, the EDID tells the audio decoder the display can't get audio information on that way. Therefore the Rotel stays silent.
              Perhaps Rotel has implemeted the HDMI standard with the audio information in EDID too close. Actually they should ignore this information and decode the signal if the related setup is "AMP MODE".

              Best regards,
              Alfred
                • Bottom

                Comment

                • mbischo
                  Junior Member
                  • Jul 2009
                  • 2
                  #5
                  The issue is resolved with the latest firmware updates (Main 1.1.6, HDMI-Board 1.1.2, and DSP-Board 1.1.2). I had the same EDID problem and the updates fixed it
                    • Bottom

                    Comment

                    • AudioDude
                      Junior Member
                      • Jan 2009
                      • 8
                      #6
                      Hello,
                      Didn't notice a reply, do you know the date of the firmeware?
                      Regards,
                        • Bottom

                        Comment

                        • mbischo
                          Junior Member
                          • Jul 2009
                          • 2
                          #7
                          According to the filenames the dates should be this:

                          DSP 12/15/2008
                          HDMI 03/25/2009
                          MAIN 04/24/2009
                            • Bottom

                            Comment

                            Previous template Next

                            Related Topics

                            Collapse
                            • psrontom
                              Non-HDCP FP, HDCP DVD player - how to?
                              by psrontom
                              I just got my SE 20HD projector, and am in the hunt for my new DVD player with DVI/HDCP/HDMI output. I'd rather not go Bravo D1 because of its poor reliability issues... and it's the only non-HDCP player I know of.

                              To my knowledge, one device can strip / decode the HDCP from the DVI data,...
                              22 October 2004, 18:46 Friday
                            • cdika17
                              RSP-1570 AND XBOX 360 elite ISSUES
                              by cdika17
                              I have mentioned this on another thread but it's lacking feedback, so i fiugred i'd start my own thread.

                              When i have my xbox360 hooked up, the hdmi feed drops out, then in and out. Signal loss then comes back for a sec, i shut everything off, did factory default, still doing it, any suggestions?...
                              25 September 2009, 14:34 Friday
                            • bluray
                              1570: HDMI in; Component Video out?
                              by bluray
                              I want to run component video from the 1570 to a TV (no available HDMI input on TV due to equipment that I want to keep directly connected to it). Can other video inputs (BD player and Roku) to the 1570 be HDMI with the 1570 then outputting the picture via component video? Thank you.
                              10 August 2009, 22:00 Monday
                            • Andrew M Ward
                              What is HDMI 1.3 (and who should care)
                              by Andrew M Ward
                              The seven HDMl Founder companies (Hitachi, Ltd.; Matsushita Electric Industrial Co., Ltd.; [Panasonic]; Philips Consumer Electronics International B.V.; Silicon Image, Inc.; Sony Corp.; Thomson, Inc.; and Toshiba Corp.) at the recent International Consumer Electronics Show (CES) highlighted key capabilities...
                              01 March 2006, 15:23 Wednesday
                            • Patrick TX
                              1066 component switching question?
                              by Patrick TX
                              I have a new 1066 as well as a new Pioneer Elite Pro630HD RPTV. It only has 2 component inpus, as well as 2 HDCP DVI inputs. Right now I have no DVI devices, and 3 component devices. A Panasonic DVD-RP91K for 4:3 an non-anamorphic DVD's, and a Panasonic DVD-XP30 for everything else. I also have an HD...
                              20 July 2003, 12:42 Sunday
                            • Loading...
                            • No more items.
                            Working...
                              Searching...Please wait.
                              An unexpected error was returned: 'Your submission could not be processed because you have logged in since the previous page was loaded.

                              Please push the back button and reload the previous window.'
                              An unexpected error was returned: 'Your submission could not be processed because the token has expired.

                              Please push the back button and reload the previous window.'
                              An internal error has occurred and the module cannot be displayed.
                              There are no results that meet this criteria.
                              Search Result for "|||"