RMB1075 channel dead

Collapse
This topic is closed.
X
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • JP
    Member
    • Feb 2003
    • 32
    #1

    RMB1075 channel dead

    Hey guys, so this has happened in the past. ( I drop an RCA cable and it falls on the positive/negative speaker terminals, I curse myself and then replace the fuse kinda thing) This time though, no such easy resolution. I come back from vacation just 2 days ago. The power had gone out a few days earlier, no big deal it happens. I have a MonsterCable HTS3500 surge/line filter on a dedicated 20 amp circuit. (I'm not worried) I turn the surge back on and then I turn the amp on. The front right speaker crackles for a bit. Other than that everything seems fine. So I start watching all my previous TIVO stuff. I don't notice the right speaker working until I start to play some XBox. No sound at all! So, I disconnect cables and pull the amp out. Check the fuses, they look OK, so I check cables, and check cables, and check some more. Everything looks good. So I pull it out again, I test each individual channel with 1 incomiong signal and the front right speaker. They all work except for the right side of the amp. Uggghhhhh All the fuses are good, I don't see any damage on the boards, and I am at a loss. any ideas?? I already contacted Rotel service and am waiting to hear back. But I am moving so this may be a problem. I can't take it to my 'dealer' because I bought it from Rotel directly. (don't ask) Thanks to all!!

    JP
    Tags: None
      • Bottom
    • Andrew Pratt
      Ultra Senior Member
      • Aug 2000
      • 16478
      #2
      sorry other then making sure the fuses are ok I'm not sure what else you might be able to do. Is the protection light lite up on the front of the unit?




        • Bottom

        Comment

        • JP
          Member
          • Feb 2003
          • 32
          #3
          Andrew, yes the lights come on. So im at a loss. A friend of mine is going to drive it up to Rotel in Reading, MA as I am already in California

          thanks!

          jp
            • Bottom

            Comment

            Previous template Next

            Related Topics

            Collapse
            • sajaga
              RB1080 just serviced - 6.3A fuses again!!
              by sajaga
              Hey all,

              my RB1080 died a few weeks back - the old no left channel trick!!
              I am local in Melbourne and dropped it off to International Dynamics in Richmond. I explaind to them what Aussie Geoff had gone through with them personally, as I am sure many of you all have in your various...
              22 March 2005, 23:34 Tuesday
            • paulpegg
              Rotel RSX-1055 hit by power surge
              by paulpegg
              A few days ago a sudden storm and nearby lightning hit caused a power failure with a big boom, outside where the lightning hit and inside through the speakers in my system. The plasma screen also went pure white before going down. When the power was restored, everything worked except there was no audio...
              06 August 2006, 08:24 Sunday
            • John
              RB991 or 1080 fuses blowing !!!
              by John
              Hello everyone, im new here but i couldnt resist, as ive had nothing but blowing fuses since ive owned my RB991 ( same as the 1080 apart from the remote trigger)

              So far :my amp was originally driving 4 ohm sub in an enclosed space, fuses would blow on a regular basis, Lots of blame went...
              29 June 2004, 05:07 Tuesday
            • rotel&energy
              Loss of center channel (RSX-1055)
              by rotel&energy
              Recently, I've had some problems with the center channel of my
              RSX-1055 (completely up-to-date firmware). When I run a test tone through each speaker in my system (5.1), all of the speakers sound normal except the center channel. I have to raise the volume on the 1055 to 70+ in order to hear...
              27 December 2006, 09:45 Wednesday
            • belzarrath
              Help on which fuses to get
              by belzarrath
              Last week I blew two fuses in my RB985. The fuses are to old to read.
              I believe they are a 6amp 125volt porcelian fuse. I do not know if they are fast or slow blow fuses, I assume it is fast blow.

              Can anyone verify the type of fuses which I need. I am also having trouble finding...
              06 April 2008, 22:55 Sunday
            • Loading...
            • No more items.
            Working...
              Searching...Please wait.
              An unexpected error was returned: 'Your submission could not be processed because you have logged in since the previous page was loaded.

              Please push the back button and reload the previous window.'
              An unexpected error was returned: 'Your submission could not be processed because the token has expired.

              Please push the back button and reload the previous window.'
              An internal error has occurred and the module cannot be displayed.
              There are no results that meet this criteria.
              Search Result for "|||"