Question: what do people use to connect the wires to the drivers? Should I be concerned about any additional added resisted by these types of connectors?
Do they make these kinds of things in a more conductive material?
Another Statements HT (Monitors, Statements II, Statements II Center)
Collapse
X
-
- Bottom
Leave a comment:
-
Made some more progress this week. I finished laminating the 1/8" HDF on the top and two sides of both cabinets, flush trim routed all sides of both cabinets, put a round over on the front and top and have all surfaces sanded with 120grit in prep for Duratex.
Here is tower number two just after finishing with it for today.
Both towers ready for Duratex!
Lots of dust, glad I have a large box of these things
- Bottom
Leave a comment:
-
Congrats! The subs, even at 300W should hit hard. I used basically the same amp for my 15" driver build, but in plate format. I think you will be very happy once dialed in!- Bottom
Leave a comment:
-
No new progress on the towers, but I've finished all the glue work on the four sub enclosures, I hope to have a chance this weekend to do a flush route around them.
It also looks like I've decided on sub amps, I went with the Dayton SA1000 stand alone amps, four of them.- Bottom
Leave a comment:
-
Thanks, I hope someone gets a small portion of help from my postings as I've gotten from other's posts around here!
The cabinet you see up there above with the round overs, that is the one with the whole in the top of the cabinet
- I sandwiched the whole with a piece of MDF on the bottom and the HDF on the top.
- Bottom
Leave a comment:
-
Love all the pictures you're posting. Very cool project; the crossovers look especially handsome.
If you haven't decided what to do with the extra cabinet hole yet, you could rabbet it and cut a matching circle to close it up.- Bottom
Leave a comment:
-
I was able to get a bit more work done today before I leave for a week. I have one sub cabinet completely glued together and the second one half way there.
One tower is ready for Duratex. Both sides and top laminated with 1/8" HDF, 3/4" roundover on front and top, HDF sanded with 80 grit to take off the sheen and allow the Duratex to adhere to the surface.
The roundover is also sanded with 320 to make it very smooth. The lines you see are glue, though they do appear as though they're gaps, they're not.
- Bottom
Leave a comment:
-
I've heard you can dilute it something like 20% - but after testing with it this weekend I've been able to copy a few others around here who've suggested rolling with a dry roller about 2-3 minutes after each coat. I tried that, as well as also running it down with my bare hands about 2-3 minutes after each coat and that worked really well. My test piece has almost a leather texture, pretty smooth, but not spray paint smooth.
Awesome, thanks for that!As for atmos speakers, I built my own! They use 4 Faital 4" drivers each and match very nicely with the Statements and Finalists once dialed in. I have a build thread somewhere on here... https://www.htguide.com/forum/showth...ighlight=Atmos
I'm still not sure what I'll be powering the subs with. Based on my preliminary WinISD calculations and previous REW measurements and the corresponding needed EQ curve, I'll bottom them out with 300 watts, so I don't need a lot of power. I have two free channels on my XPA-7 that I'll probably use initially for the first two. I'm definitely open to options, though I'm not really interested in Pro amps.- Bottom
Leave a comment:
-
Very nice!
Careful watering down the duratex, as you will change the molecular composition and I am not sure the finish will be what you want. I suggest a foam roller - as the roller (I used spray grade) will lay a fairly textureless finish.
As for atmos speakers, I built my own! They use 4 Faital 4" drivers each and match very nicely with the Statements and Finalists once dialed in. I have a build thread somewhere on here... https://www.htguide.com/forum/showth...ighlight=Atmos
What do you plan to power the sub with? A trick is to use zip ties in the driver's holes (2 opposing) so that you can lower it into and back out of the hole to mark and then drill your seats.- Bottom
Leave a comment:
-
- Bottom
Leave a comment:
-
I laminated the sides of one of the towers, and the top of the center this weekend with HDF and ran a flush trim router around the edges to clean it up.
I purchased a 2" long flush trim bit and realized when it arrived on Friday that both my routers were 1/4" shank only...*sigh*. Thankfully, there is a Woodcraft less than 3 miles from my house and they had a "Trade in" sale going on. Picked up a Porter Cable router with a trade in, got it home, and realized that the router plate didn't have a big enough center whole to fit the 3/4" roundover bit! *Double Sigh*. So, I made my own!
It is amazing how much dust one of these 3/4" roundover bits creates.
The plan is to laminate a layer of HDF on the tops of the cabinet and complete the round over on the top as well.- Bottom
Leave a comment:
-
I've used 1/8" MDF to cover the joints for some time and it works well. You end up with a very small seam rather than a bunch. This time I'm also coating the cabinet with Zinsser Guardz that soaks in and makes a very hard surface that I will then skim coat the few joints with bondo. I'm going to shoot these in gloss black so they have to be perfect or everything will show. My plan is to sand thoroughly and then skim the whole cabinet with Crystalac grain filler before the final sanding. Then onto high build primer and then shoot it with Crystalac gloss black with top coats of Crystalac gloss clear.
If I shoot it well enough it shouldn't take too much rubbing to make it look good.
When I bought my Mustang, I invested in a DA buffer and many foam pads to get as close as I could to a show car finish. So, my cabinet plan is, a light sanding with 2000, buff with Meguires 105, then buff Meguires 205 and finally buff with Menserna SF3800 to jewel the finish. I'll than apply the left over Polish Angel Invincible and Cosmic coating I applied to my black Mustang.
Sorry if that's too much information. 8O I have high hopes they'll be quite pretty when I get done.
Jim- Bottom
Leave a comment:
-
-
jwanck11, thank you for this perspective, really appreciate it. My statements builds are going into a dedicated theater/listening space that is very dark, so the duratex just might work out very well for my environment! I keep tossing around the idea that I might want a set of curved cabinets with a nice wood veneer for the front two speakers, and then put accent lights that are controlled with a 12v trigger so that they shut off when the projector is turned on....we'll see....for now though, I'm strongly leaning toward duratex so that they disappear into the room.Thanks guys! The system gets so many compliments - especially when I put on an orchestra piece at low to moderate volume. People cannot believe how such "big" speakers can disappear while producing a concert hall experience. You can literally hear depth. They blow away my much more expensive D4s.
I completely agree that vision taste is in the eyes of the beholder.... I just wanted to give the OP a chance to see how duratex looks. On that note, if you do choose to go that route, make sure you let the Duratex cure for at least a week before setting them in place. It is hard as heck to be patient, but worth it.
Yep - I was going to go with a DIYSG design for the dedicated theater due to the very high sensitivity, but the Statements are flat out incredible for movies given the additional spacial effect. Rather than a wall of sound, I prefer an environment of sound. The amp I use can push them plenty loud enough to create an immersive experience. I have the CC built, have 2 SI DS4 18" drivers I'll be putting in ~8cuft ported enclosures, the statement IIs as mains and likely another set (4) of Finalists for RS and RB. My atmos speakers are already built. I will try another design or two because building speakers is a lot of fun, but I have a master and princess suite bathrooms to get to after the theater. lol.
I'd like to make the Duratex finish as smooth as possible, I have some smooth foam rollers that I've picked up and was also planning on adding a bit of water to the Duratex (Roller grade) to help keep it smooth. How much water is appropriate?
Out of curiosity, jwanck11, what are you using for atmos speakers? I'm struggling with this at the moment.
On another note, I've laminated two sides of one tower with 1/8" HDF. I chose to do this in an attempt to reduce or eliminate telegraphing of the side glue joints. Is this over kill? Jim, seem to remember a thread where you were trying this with a set of speakers you built recently, am I remembering that correctly? The plan is to do the two sides and top of each of the towers and the center channel.- Bottom
Leave a comment:
-
Jwanck11,
"but I have a master and princess suite bathrooms to get to after the theater. lol. " You've got your priorities straight! Good Man.
Ron- Bottom
Leave a comment:
-
Thanks guys! The system gets so many compliments - especially when I put on an orchestra piece at low to moderate volume. People cannot believe how such "big" speakers can disappear while producing a concert hall experience. You can literally hear depth. They blow away my much more expensive D4s.
I completely agree that vision taste is in the eyes of the beholder.... I just wanted to give the OP a chance to see how duratex looks. On that note, if you do choose to go that route, make sure you let the Duratex cure for at least a week before setting them in place. It is hard as heck to be patient, but worth it.
Yep - I was going to go with a DIYSG design for the dedicated theater due to the very high sensitivity, but the Statements are flat out incredible for movies given the additional spacial effect. Rather than a wall of sound, I prefer an environment of sound. The amp I use can push them plenty loud enough to create an immersive experience. I have the CC built, have 2 SI DS4 18" drivers I'll be putting in ~8cuft ported enclosures, the statement IIs as mains and likely another set (4) of Finalists for RS and RB. My atmos speakers are already built. I will try another design or two because building speakers is a lot of fun, but I have a master and princess suite bathrooms to get to after the theater. lol.- Bottom
Leave a comment:
-
Your system looks very nice, some prefer the drivers / speakers to "disappear" into the room when watching a movie in the dark. I'm sure it sounds fantastic.
Already working on another build? Impressive, Most impressive, to borrow a saying from E.T.
Ron- Bottom
Leave a comment:
-
Sweet system! :WI used Duratex.... and now that I have had them in my LR for awhile, I wish I would have gone a different route (and will with my next build.) Duratex is very easy to apply - you just have to work quickly and keep the roller wet to end up with a uniform finish.
The issue is that the drivers sort of get "lost" and the speaker loses its identity, at least to me. I'll take pictures and post them...
JimLast edited by theSven; 30 April 2023, 15:34 Sunday. Reason: Remove image links that are no longer available- Bottom
Leave a comment:
-
If there are any more pictures that would help with your perspective, let me know! I am going to move these into the basement and build another set (already have the center channel built) and finish them differently.- Bottom
Leave a comment:
-
I used Duratex.... and now that I have had them in my LR for awhile, I wish I would have gone a different route (and will with my next build.) Duratex is very easy to apply - you just have to work quickly and keep the roller wet to end up with a uniform finish.
The issue is that the drivers sort of get "lost" and the speaker loses its identity, at least to me. I'll take pictures and post them...
Images not available
- Bottom
Leave a comment:
-
Duratex delivered! I'm about 95% sure I'm going with duratex for the center, will be testing the product this week. My goal is to have the center completed by this weekend.- Bottom
Leave a comment:
-
-
-
-
Curt and I really appreciate your kind words. That means a lot to us. However, the thing we are happiest about is that you're enjoying the speakers. :T
Jim- Bottom
Leave a comment:
-
You are going to absolutely be amazed when you light these up.
I have never been disappointed with any of Curts designs and Jim Holtz is a big help on these builds as well, great guys with a lot of knowledge.- Bottom
Leave a comment:
-
kPnaz,
Looking good, glad to see your progress even though free time is a fleeting thing. It's journey that's fun.
The glue blocks are a good idea. If you would like any online help with the finish these, just ask. We'll be glad to help. I've built a few that came out pretty good.
Ron- Bottom
Leave a comment:
-
Forgot to mention, I also added a few "glue blocks" in the corners in the base of the cabinet. I did this to give extra material for bolts to bite into in order to hold the base on. You can see them in the middle picture above.- Bottom
Leave a comment:
-
I started a new job a little over two months ago, and life has been crazy. The common phrase from coworkers is "Drinking from a fire hose", and they're right! Needless to say, it has really slowed down progress on my Statements.
Today I finished wiring up the second tower, glued in all the foam, and glued on the front baffle. I put a bead of hot glue on the wiring to keep it tight against the tunnels, as well as filled the whole in the tunnels where the wire fits through using hot glue.
A few weeks back, a neighbor of mine helped me make cuts into the base peices using a band saw with a fence. All the cuts are incredibility consistent. here's a shot of a few of the boards. The image makes it look like the cuts are angled outward, but they're not, they're paralleled with the outside edge.
Hopefully tomorrow I can have the second tower to the same point. The center cabinet is pretty well completed, flush routed, sanded and ready to be finished. Still not decided how I'll finish it.- Bottom
Leave a comment:
-
You have been making excellent progress- no motivational speeches required, I can see- success will be it's own motivation.- Bottom
Leave a comment:
-
Thanks, Kevin, I hope my finished products look as great as yours when I'm finished. I'm beginning to wish I would have just bought yours! - But then my wife reminded me that I wouldn't be able to point to them and say "I built those"!
- Bottom
Leave a comment:
-
-
I'm done with all of the cabinet glue-up for the center, I need to do some flush trim routing, sanding and prep for finishing. I've still not decided on how I want to finish it. Tossing around the idea of going with black Duratex, but may decide to veneer it. We'll see.
Crossovers and internal wiring for one tower complete, one more to go! - I'll post a picture of the wiring at a later point. Electronics and wiring checked out! Need to do a small amount of trimming before I can glue on the baffle.
- Bottom
Leave a comment:
-
I forgot to post this earlier on in the thread. This is how I made sure my additional bracing was both level and exactly the right width in the cabinet. I used some small strips of MDF clamped to the back of the cabinet, the window brace and one of the 5"x10" braces and another strip a along the front of the cabinet. I then clamped my side brace that goes from front to back under these small strips of MDF. I then used alligator clamps to hold my side-to-side brace. I'm not sure if I'm explaining it very well, hopefully the picture helps.
- Bottom
Leave a comment:
-
-
Wired up the center to test the crossovers, everything sounded fine, so I'm gluing on the top now, and I'll glue on the baffle later this week, time permitting. The Vifa mids don't fit in the holes as the binding post gets in the way. I'll try to post a pic of it from the back side. I suspect that once I chamfer the back of the mid hole, it should fit nicely.
Cut all of the foam for the towers, that's a lotta foam!
- Bottom
Leave a comment:
-
I started a new job last week, so progress will be a bit slow as I ramp up in my new role. I did get to spend a bit of time today working on "little" stuff.
This is a shot of the cabinets as I left them from last weekend. Haven't done anything with them this past week except put a block of MDF over the hole that is visible on the left tower at the bottom of the cabinet. I'm doing the same thing with the towers and center that I did with the Monitors. I've cut square holes in the back of each cabinet and then covered them with a piece of MDF so that the binding posts are "sunk" down below the surface.
One of my braces I got a bit too happy with the power sander and took a bit too much material off the brace. I mixed up some MDF dust and glue to create my own "wood filler". It is as hard as a rock! Seems to have done the job pretty well.
The center is at about the same stage as the towers. Still quite a bit more work to go!
Any thoughts on crossover placement?
I used a piece of MDF glued to the cabinet as a mounting block for the woofer circuit. I did this on the towers as well, but it is easier to see on the pic of the center. I chose to do this so that there was more material to "bite" into with screws. I wanted the extra material because of the weight of the woofer circuit. They'll be mounted with deck screws, pilot holes drilled, of course.
And the Mid/tweet cavity lined with foam. I cut out sections of foam around the crossovers.
- Bottom
Leave a comment:
-
Progress so far:
- crossovers are finished and ready to mount.
- Internal wiring has been cut to length and zip tied ready to be secured inside the cabinets.
- Cut the circular holes for the terminal cup into a square hole to recess binding posts instead, very similar to what I did for the Monitors on page 1.
- Cut a circle out of the bottom of the goofed up cabinet for the port tube
- Cut mounting block for woofer circuit, to give more depth for larger screws to hold the boards in place (will add a picture of that later.)
All components are either zip tied or screwed into place (Zister resisters).
I then used hot melt glue to keep the larger components from rattling, and to secure the terminals.
All connections between components were secured before solder was applied.
Here I'm gluing on the second side of one cabinet, will do the other in the morning. Then I need to sand the bracing flush with the side panels in preparation for the baffle glue up.
Once all the sanding is finished, I'll vacuum out the cabinet, glue in a few more pieces, secure internal wiring and crossovers and start fitting the foam.- Bottom
Leave a comment:
-
PKnaz, it's not a goof up, it's a feature! You invented a new speaker called "The Dolphin". JK. You're fix sounds like a good idea / save. Nice job on the extra braces.
Thanks for the pictures and updates.- Bottom
Leave a comment:
Related Topics
Collapse
-
by impala454This thread will document my build of a complete 7.1 set of Statements (with sub). Note: This set was started with only my second build ever. Please take all of this thread with a large grain of salt. My motive in posting it was just to give a DIY newbie's experience which might help out other newbies....-
Channel: Mission Possible DIY
-
-
by Jim HoltzA full description and plans are now available on Curt's website!
My musical reference!
Statements II – An evolution for the music lover!
The Statements II are the result of the Finalists project which focused on achieving the best midrange possible but with an eye on...-
Channel: Mission Possible DIY
-
-
by impala454I have a small apartment and am working to downsize my stuff somewhat. I was wondering if it would be difficult (or maybe even if it already exists) to design a MT only speaker for use as surrounds, using the existing Statements MT drivers (the Tang Band 1337 and Fountek NeoCD 3.0). I realize it wouldn't...-
Channel: Mission Possible DIY
-
-
by impala454I have four Statements Monitors and love them, however I'm finding I'd like my rear channels to be smaller in size, and figured the Lineup R4 would be perfect. I could re-use the drivers and just build the R4 boxes. I've taken a look at the two designs and noticed there's not much re-use in the crossover...-
Channel: Mission Possible DIY
-
-
by Jim HoltzYou can't have a new speaker without a new center channel to compliment it for home theater.
Statements II and The Finalists Center Channel
During the last several years the original Statements have been frequently used as mains for home theater systems. The original Statements...-
Channel: Project development
-
- Loading...
- No more items.

Leave a comment: