Is it possible....

Collapse
This topic is closed.
X
X
 
  • Time
  • Show
Clear All
new posts
  • Dave Duvall
    Junior Member
    • Jan 2001
    • 12

    Is it possible....

    ....to use the pink noise channel levels off a test DVD and set the levels of your speakers using the Ref 30, or are you limited to only the signal generator from within the processor?

    See ya. Dave
  • Jerry Pease
    Member
    • Aug 2000
    • 37

    #2
    I am not sure exactly what you are asking, but you can use the B&K-Ref30 internal tones or DVD with test tone i.e. Avia and get the same results.

    Hope this helps,




    JP
    JP

    Comment

    • John Kotches
      Moderator Emeritus
      • Jan 2001
      • 140

      #3
      Sort of.

      You can't really adjust the individual channel trims with the Ref 30....

      You can adjust the fronts, rears, CC and sub, but you can't get at FL, FR, RL and RR individually without running the B&Ks calibration tones.

      Regards,




      ---
      Editor, PC/Home Theater
      Secrets of Home Theater and High Fidelity
      My Home Theater
      NEC LT-150 specific page.
      ---
      Editor, PC/Home Theater
      Secrets of Home Theater and High Fidelity
      My Home Theater
      NEC LT-150 specific page.

      Comment

      • Dave Duvall
        Junior Member
        • Jan 2001
        • 12

        #4
        Reply to Jerry Pease's post:

        I can't seem to figure out how to adjust the levels using other than the internal noise generator, which runs each time you go to speaker levels on the setup menu. I know you can do the temporary, on the fly, changes on the remote to some of the channels, but you lose those levels after you turn the unit off or put it in sleep mode.

        See ya. Dave

        Comment

        • Dave Duvall
          Junior Member
          • Jan 2001
          • 12

          #5
          Quoting John Kotches:

          >>You can't really adjust the individual channel trims with the Ref 30....>You can adjust the fronts, rears, CC and sub, but you can't get at FL, FR, RL and RR individually without running the B&Ks calibration tones.<<

          That's with the buttons on the bottom of the remote, if I'm on the same page with you here. Unfortuately, those are lost each time you shutdown.

          Thanks.

          See ya. Dave

          Comment

          • John Kotches
            Moderator Emeritus
            • Jan 2001
            • 140

            #6
            You might have a later rev of the remote, mine only has CC, Sub, Surrounds, no Front.

            So if you hit + for Surrounds, you raise the level of BOTH surrounds.

            THat's the point I'm getting at.

            Regards,




            ---
            Editor, PC/Home Theater
            Secrets of Home Theater and High Fidelity
            My Home Theater
            NEC LT-150 specific page.
            ---
            Editor, PC/Home Theater
            Secrets of Home Theater and High Fidelity
            My Home Theater
            NEC LT-150 specific page.

            Comment

            • John Kotches
              Moderator Emeritus
              • Jan 2001
              • 140

              #7
              Doh! Sorry for the duplicate post.

              Regards,




              ---
              Editor, PC/Home Theater
              Secrets of Home Theater and High Fidelity
              My Home Theater
              NEC LT-150 specific page.
              ---
              Editor, PC/Home Theater
              Secrets of Home Theater and High Fidelity
              My Home Theater
              NEC LT-150 specific page.

              Comment

              Working...
              Searching...Please wait.
              An unexpected error was returned: 'Your submission could not be processed because you have logged in since the previous page was loaded.

              Please push the back button and reload the previous window.'
              An unexpected error was returned: 'Your submission could not be processed because the token has expired.

              Please push the back button and reload the previous window.'
              An internal error has occurred and the module cannot be displayed.
              There are no results that meet this criteria.
              Search Result for "|||"